Profile overview for abruski.
Submission statistics

This user has mostly submitted to the following subverses (showing top 5):

1 submissions to 3DPrinting

1 submissions to DnB

1 submissions to ImGoingToHellForThis

This user has so far shared a total of 2 links, started a total of 1 discussions and submitted a total of 3 comments.

Voting habits

Submissions: This user has upvoted 12 and downvoted 0 submissions.

Comments: This user has upvoted 3 and downvoted 0 comments.

Submission ratings

5 highest rated submissions:

We ruined our countries so we need a new place to ruin, submitted: 7/6/2015 12:06:06 PM, 91 points (+98|-7)

Huge collection of early LTJ Bukem Mixes, submitted: 7/6/2015 12:08:11 PM, 9 points (+9|-0)

Finishing PLA prints, submitted: 6/13/2015 9:22:31 AM, 6 points (+6|-0)

5 lowest rated submissions:

Finishing PLA prints, submitted: 6/13/2015 9:22:31 AM, 6 points (+6|-0)

Huge collection of early LTJ Bukem Mixes, submitted: 7/6/2015 12:08:11 PM, 9 points (+9|-0)

We ruined our countries so we need a new place to ruin, submitted: 7/6/2015 12:06:06 PM, 91 points (+98|-7)

Comment ratings

3 highest rated comments:

Finishing PLA prints submitted by abruski to 3DPrinting

abruski 0 points 1 points (+1|-0) ago

Acetone does not work on PLA

Has anyone had any success building an open source or kit 3d printer or CNC mill? Would you do it again? What lessons did you learn? About to take the plunge. submitted by wtmvafaf to 3DPrinting

abruski 0 points 1 points (+1|-0) ago

I designed and assembled a 3d printer. Went for CoreXY because the structure does not twist and you have only one moving motor if you go for a direct extruder. Here are some things I learned

  • H7 Steel Rods no less than 10mm diameter

  • If you go for bearings don't buy cheap shitty bearings.

  • PTFE, PLA, igus bushings are better. They are quiet and don't ruin your rods

  • Enclosed printer is needed for ABS, because it curls on itself if there is no heating.

  • ABS is easier to sand and finish than PLA

  • You'll get injured. Be prepared for burns, cuts, bumps

Voat, the student side-project is now Voat, Inc.! submitted by Atko to announcements

abruski 0 points 0 points (+0|-0) ago

You should have stayed anon.

3 lowest rated comments:

Voat, the student side-project is now Voat, Inc.! submitted by Atko to announcements

abruski 0 points 0 points (+0|-0) ago

You should have stayed anon.

Finishing PLA prints submitted by abruski to 3DPrinting

abruski 0 points 1 points (+1|-0) ago

Acetone does not work on PLA

Has anyone had any success building an open source or kit 3d printer or CNC mill? Would you do it again? What lessons did you learn? About to take the plunge. submitted by wtmvafaf to 3DPrinting

abruski 0 points 1 points (+1|-0) ago

I designed and assembled a 3d printer. Went for CoreXY because the structure does not twist and you have only one moving motor if you go for a direct extruder. Here are some things I learned

  • H7 Steel Rods no less than 10mm diameter

  • If you go for bearings don't buy cheap shitty bearings.

  • PTFE, PLA, igus bushings are better. They are quiet and don't ruin your rods

  • Enclosed printer is needed for ABS, because it curls on itself if there is no heating.

  • ABS is easier to sand and finish than PLA

  • You'll get injured. Be prepared for burns, cuts, bumps